본 가이드는 캐나다 일반 주택(Wood-Frame) 또는 합판/석고보드 벽체에 바풀 월바를 설치하는 방법을 안내합니다.
This guide explains how to install the Bapull wall bar in a typical Canadian wood-frame house or on a plywood/drywall wall.
안전한 사용을 위해 설치 전 모든 안내사항을 읽고, 필요한 도구와 부품을 준비해주세요.
For safe use, please read all instructions and prepare the necessary tools before proceeding.
설치 전 확인사항 Check Before Installation
-
월바는 운동기구이며, 하중을 견딜 수 있는 구조체에 고정해야 합니다.
The wall bar is exercise equipment that requires secure anchoring to a structural support that can bear the load. -
캐나다 일반 주택의 내벽은 석고보드(Drywall) 뒤에 목재 스터드(Wood Stud)가 보통 16인치 간격으로 배치되어 있습니다.
In a typical Canadian interior wall, wooden studs are placed at regular intervals (usually 16 inches) behind the drywall. -
월바 설치 시 반드시 스터드에 직접 고정해야 합니다. 석고보드(Drywall)만으로는 하중을 지탱할 수 없습니다.
The wall bar must be anchored directly into the studs; mounting only to drywall may cause failure.
필요한 도구 Required Tools & Materials
| Stud Finder | 스터드 파인더 |
| Power Drill & Bits | 전동 드릴 & 비트 |
| Level | 수평계 |
| Pencil or Marking Tool | 연필 또는 마킹 도구 |
| 6 mm Drill Bit (Pilot Holes) — Optional | 6mm 드릴비트 (파일럿 홀용) — 선택 |
| 8–10 mm Wood Screws | 8-10mm 나사 |
| Washers (if needed) | 와셔 (필요시) |
| Spanner or Wrench | 스패너 또는 렌치 |
설치 방법 Installation Steps
Step 1. 스터드 찾기 | Find the Studs
- 스터드 파인더를 사용하여 벽 내부 스터드 위치를 확인합니다. 월바는 최소 2개 이상의 스터드에 걸쳐 고정해야 합니다. 스터드는 보통 16인치 간격입니다.
Use a stud finder to locate studs inside the wall. The wall bar must be secured across at least two studs, typically spaced 16 inches apart. - 스터드 위치를 연필로 표시합니다.
Mark the stud locations with a pencil. - 수평계를 사용하여 가이드라인을 그려 월바가 수평이 되도록 합니다.
Use a level to draw a guideline so the wall bar is perfectly horizontal.
Step 2. 파일럿 홀 뚫기 | Drill Pilot Holes
- 월바의 고정 구멍 위치가 표시한 스터드와 일치하도록 정합니다.
Align the wall bar mounting holes with the marked stud locations.
<Optional> 6mm 드릴비트로 파일럿 홀을 뚫으면 나사가 더 쉽게 박힙니다.
Drill pilot holes using a 6mm drill bit. This helps the screws go in more easily.
Step 3. 월바 고정 | Secure the Wall Bar
- 월바를 벽에 대고 나사를 구멍에 맞춰 조여 고정합니다. 나사가 스터드에 정확히 박히도록 확인합니다.
Place the wall bar against the wall and tighten the screws through the holes. Make sure the screws are driven precisely into the studs. - 필요시 와셔를 사용하여 고정력을 높입니다.
If needed, use washers to increase holding strength. - 월바 전체가 흔들림 없이 단단하게 고정되었는지 최종 확인합니다.
Check that the entire wall bar is firmly secured without wobbling.
설치 체크리스트 Installation Checklist
- ☑ 스터드 파인더로 스터드 위치 확인 | Locate studs with a stud finder
- ☑ 수평 가이드라인 표시 | Draw a level guideline
- ☑ 파일럿 홀 뚫기 (선택) | Drill pilot holes (optional)
- ☑ 스터드에 단단히 고정 | Secure to wooden studs
- ☑ 흔들림 최종 확인 | Final wobble check
주의사항 Important Notices
-
석고보드(Drywall)만 있는 벽에는 설치하지 마세요. 반드시 벽 내부의 목재 스터드에 고정해야 합니다.
Do NOT install on an area with only drywall. It must be anchored to the wooden studs inside the wall. -
스터드를 찾을 수 없거나 벽체 구조가 약한 경우, 먼저 보강 패널(합판 등)을 벽면에 시공한 후 그 위에 월바를 설치하는 것을 권장합니다.
If you cannot locate the studs, or if the wall structure is weak, we recommend first installing a reinforcement panel (such as plywood) across the wall and then mounting the wall bar onto that panel. -
스터드 간격과 월바 고정 구멍 간격이 맞지 않는 경우, 전문 시공업체에 문의해주세요.
If the stud spacing does not match the wall bar mounting spacing, consult a professional.
궁금한 점이 있으시면 마마랑 고객센터로 문의해주세요.
If you have any questions, please email @ info@mamarang.com
BAPULL — with every tomorrow, a lifestyle rowtines
Designed by Rowspace | Imported by Mamarang